|
|
Enquiry
|
|
Click on image for larger photo
|
Product Code:
B9202
TRAILER JACK 3180KG CAP 70MM X70MM BOX
LEG RETRACTED: 520MM EXTENDED 890MM
SCREW TRAVEL 370MM WITH FLAT BASE PLATE
|
|
|
|
|
Please enter a valid quantity |
|
|
|
|
 |
|
|
|
TRAILER JACK 3180KG CAPACITY 70MM X 70MM BOX BODY 890MM MAX LIFT
NOTE WINDING CAPACITY IS ONLY 2000KG
HAS NO MOUNTING BRACKET SUPPLIED
SIDE WINDING HANDLE IS 250MM LONG ( GEAR BOX ON TOP OF JACK )
MOUNTING BRACKET TO SUIT IS PART NO (B8695)-(S-21625) & (XY7000E) IS WELD ON FLAT TYPE (S-4068) OR (B8695)
TOTAL HEIGHT EXTENDED 1000MM CLOSED HEIGHT IS 630MM
BASE PLATE SIZE 150MM X 210MM CAN BE ROTATED
LENGTH OF SCREW TRAVEL: 370MM
MAXIMUM LIFT - 890MM
MINIMUM LIFT - 520MM
SCREW TRAVEL - 370MM
JACK STEEL HOUSING SIZE BOX SECTION 70MM X 70MM
SAFETY PRECAUTIONS -
WARNING: FAILURE TO HEED THE FOLLOWING WARNINGS CAN RESULT IN PERSONAL INJURY AND/OR EQUIPMENT DAMAGE.THESE WARNINGS CANNOT COVER EVERY SITUATION, SO HAVE SAFETY FOREMOST IN YOUR MIND WHEN SETTING UP A JOB.
- READ, UNDERSTAND AND FOLLOW THE OPERATING INSTRUCTIONS AND THE ANSI B30.1 AND ASME PALD-1 SAFETY STANDARDS FOR JACKS. IF THE OPERATOR CANNOT READ ENGLISH, OPERATING INSTURCTIONS AND SAFETY PRECAUTIONS MUST BE READ AND DISCUSSED IN THE OPERATOR'S NATIVE LANGUAGE.
- WEAR EYE PROTECTION THAT MEETS THE REQUIREMENTS OF ANSI Z87.1 AND OSHA.
- INSPECT THE JACK BEFORE EACH USE; DO NOT USE THE JACK IF IT IS DAMAGED, ALTERED, OR IN POOR CONIDITION.
- TO PREVENT TIPPING, SET UP THE JACK ON A HARD, LEVEL SURFACE. SET VEHICLE PARKING BRAKE AND BLOCK TYRES.
- THE LOAD MUST NOT EXCEED THE RATED LIFTING CAPACITY OF THE JACK. LIFT ONLY DEAD WEIGHT.
- CENTER THE LOAD ON THE JACK SADDLE, BECAUSE OFF-CENTRE LOADS CAN DAMAGE SEALS AND CAUSE HYDRAULIC FAILURE.
- USE THE JACK FOR LIFTING PURPOSES ONLY. THIS JACK IS DESIGNED TO LIFT LOADS, NOT SUPPORT LOADS. IMMEDIATELY SUPPORT A LIFTED LOAD WITH JACK STANDS.
- STAY CLEAR OF LIFTED LOADS.
- USE ONLY APPROVED HYDRAULIC FLUID, SUCH AS CHEVRON AW HYDRAULIC OIL MV OR EQUIVALENT.
- THE JACK SHOULD BE USED ON HARD, LEVEL SURFACES
- THE WHEELS OF THE VEHICLE TO BE CHOCKED
- DO NOT PUT A PORTION OF YOUR BODY UNDER A VEHICLE SUPPORTED BY A JACK
- NO PERSON SHOULD REMAIN IN A VEHICLE THAT IS BEING JACKED
- DO NOT EXCEED THE WORKING LOAD LIMIT
OPERATING INSTRUCTIONS -
TO RAISE THE JACK, USE NARROW END OF JACK HANDLE TO TIGHTEN RELEASE VALVE CLOCKWISE (CW). INSERT HANDLE INTO SOCKET AND OPERATE PUMP. TO LOWER THE JACK, SLOWLY OPEN THE RELEASE VALVE KNOB BY TURNING IT COUNTERCLOCKWISE (CCW).
|
View Complete Range:
|
TRAILER PARTS > TRAILER PARKING JACKS*
TRUCK & SEMI GEAR > TRAILER PARKING JACKS*
TRACTOR ATTACHMENTS > TRAILER PARKING JACKS*
|
|
|
|
|
|
|
|
|